Analog-way Pulse2 Bedienungsanleitung
Stöbern Sie online oder laden Sie Bedienungsanleitung nach Kommunikationszubehör Analog-way Pulse2 herunter. Analog Way Pulse2 User Manual Benutzerhandbuch
- Seite / 4
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Ref. PLS350
Thank you for choosing and the . By following these simple steps, you will be able to set
up and use your powerful Dual Scaler Hi-Resoluon Seamless Switcher based on ’s new Midra™
plaorm within minutes. Discover the capabilies and intuive interface while conguring your rst
show and unleash your creavity for a new experience in show and event management.
• 1 x
• 1 x Power supply cord
• 1 x Ethernet cross cable (for device update)
• 1 x Remote Control Soware (RCS²)*
• 1 x Set of 6 audio 5-pin screw terminals
• 1 x Front Rack Ears (the parts are stowed in the packaging foam)
• 1 x User Manual (PDF)*
• 1 x Quick Start guide*
* User manual, quick start guide and the RCS² are available on www.analogway.com
You may wish to reset the unit to factory sengs to get
started. Go to:
Select the Output resoluon that matches the nave
resoluon of your display. You will next be able to choose
the output rate.
Inputs can be congured automacally using the Auto
Set All funcon.
It will scan each input and detect the sync type that is
plugged in. You can sll do an Autoset or manual setup per
input.
The has 6 layers available called: ,
, and a. Each layer will
obscure your view other layers below.
To display a source, select the (it will begin to
blink) then, select a source (it will also blink). Press
to transion your source from Preview to Program output.
There will always be a layer selected (blinking) and a source
selected (blinking) to the selected layer (blinking). To view
on Preview or change the contents of a dierent layer,
simply select it. Only 1 layer can be seen on the Preview
at once.
To display a PIP, select the (it will begin to blink)
then select your source (it will also blink). Press to
display the layer on the Program output.
To see the layer beneath, you will need to clear or move the
layers that are on top.
To clear the layer or any other layer, select the layer (it
will blink) then, select . Press to remove the
layer from the Program output.
If you want the Program and Preview to toggle/ipop
during each Take, enable this feature by going to
.
Once enabled, the old Program output will become the
new Preview aer each Take.
To record and display a Quick Frame follow the steps on
page 4.
See the next page which describes the buon lighng color
code and other front panel features.
- sources seamlessly switched in the . (Only 1 layer)
- and 1 Logo over the .
- and 1 Logo over a Frame by resizing the .
If required, front handles of the
device can be dismantled, but
with cauon. The original screws
removed must not be reintro-
duced to their locaon without
handles in place. Substanal da-
mages can occur, including risk of
electric shock from the mains vol-
tage. Only M4x12mm screws can
be used. (They are supplied with
the unit.)
Inhaltsverzeichnis
Seite 1 -
Ref. PLS350Thank you for choosing and the . By following these simple steps, you will be able to set up and
Seite 2 -
Menu scroll knobselect the output #1-2, a layer and a source, then press T
Seite 3 -
select to choose which mo
Seite 4 -
10/23/2013 - PLS350-QSGCode: 240204For complete details and operaons procedures, please refer to the User’s Manual and our website for further
Verwandte Produkte und Handbücher für Kommunikationszubehör Analog-way Pulse2
(4 Seiten)System-sensor CR-6 manuales
Manuales del propietario y guías del usuario para Equipo System-sensor CR-6.
Ofrecemos 1 manuales en pdf System-sensor CR-6 para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern